One essential aspect of achieving a top-notch vape session is priming your vape coil correctly. This guide will walk you through the entire procedure, helping you to prevent quick coil burn-outs and enhance your vaping experience. Understanding Vape Coils Vape coils, often referred to as ‘atomiser heads’, are integral components of any refillable tank in open-system e-cigarettes or vape kits. They contain the coil wire and wicking material, typically comprised of either cotton or ceramics. The wicking material is responsible for soaking up the e-liquid, which the coil wire then heats to create vapour. The Concept of Priming Priming a coil is a simple yet crucial process that involves allowing the e-liquid to fully saturate the wicking material in your coil head before the device is activated. This prevents the wick from burning when the battery is activated, which can result in a ‘dry hit’ that is unpleasant to taste. Priming is only necessary when using a new coil for the first time. The Importance of Priming Your Vape Coil The importance of priming a new vape coil cannot be overstated. Without proper priming, the coil could suffer damage due to ‘dry spots’. This can lead to a highly unpleasant burning taste, muted flavour, and reduced vapour production. If the coil is completely damaged, the cotton will burn, taste bitter, and will not function correctly, necessitating its replacement. Hence, priming a new vape coil before use is essential for a true vaping experience and to avoid premature coil replacement. The Correct Procedure to Prime a Vape Coil Identifying the Wick The first step in priming your vape coil is to locate the wicking areas on your coil. Many coils have visible holes on the outer housing, where you can see the white cotton-wicking material. Dampening the Wick Next, gently drip some vape liquid into each of these holes, rotating back to each one until they are visibly damp. Be careful not to over-saturate the wick, as this can lead to flooding. Installing the Coil Install your vape coil as per your device instructions, fill up the tank with e-liquid and then leave it alone for around 5-10 minutes. Priming Puffs After 10 minutes have passed, take 3-5 quick, sharp inhalations from your vape kit without pressing the button. This draws the vape liquid through and ensures the coil is fully saturated and ready to vape. However, be careful not to take too many sharp draws, as this can pull in too much vape liquid and accidentally flood your coil. What to Do If You Flood Your Coil It’s possible to unintentionally flood your coil while priming if too much liquid is dripped. If your coil floods, you may notice gurgling, spitting, and leakage of the e-liquid. This doesn’t mean your coil is damaged or faulty. You can expel any excess liquid by firmly flicking your vape kit away from you towards a tissue to absorb the e-liquid. Continue this process until the gurgling and spitting stop. Coil Replacement: How Often Is It Needed? The lifespan of a coil varies depending on factors like usage frequency and the type of e-liquid used. Thicker and sweeter e-liquids can shorten the coil’s lifespan. It’s time to replace the coil if you notice a burnt taste, hear gurgling when in use, or the flavour turns unpleasant. Patience is Key The length of time you should prime a vape coil depends on several factors. E-liquids with a higher PG content will take less time to saturate a coil, while those with a higher VG content, which are thicker, will take longer. However, leaving your coil to prime for as long as possible is always recommended – anywhere between 5 and 30 minutes. The longer you leave it, the better. Remember, patience and knowledge are key to not wasting coils and money. What If You Forget to Prime Your Coil? Forgetting to prime a coil is a common mistake. If this happens, especially with a low-resistance coil, don’t panic. Let it sit for a few minutes. You might have avoided damaging the coil if you don’t get a burnt taste after a puff. However, it’s still worth letting the tank sit for a while to ensure the juice thoroughly soaks into the coil. Maximising the Life of Your Coil Once you’ve mastered the art of priming, you can also explore other ways to extend the life of your coil. Always remember that a well-primed coil is the key to a satisfying and consistent vaping experience. So, take the time to do it right, and your vape sessions will be all the better for it. Happy vaping!